53’ Smooth Side Custom Trailer
Canepa Design Show Trailer
VIN: 1KKVD52211L202933
This trailer was custom designed and fabricated by Concept Transporters to showcase the state-of-the-art in racecar/collector car transportation. Since its completion it has been used only by Canepa Design at shows and west coast historic races. This trailer is in NEW condition.
Dimensions
Length: 53’
Width: 8’10”
Height: 13’ 6”
Cargo area: 50’ long, 8’ 3” wide 9’ tall
Features
• Custom Double Side Access Doors
• Concept Exterior Trim Kit
• Interior Up-grades
• Enclosed Nose Mount Generator and Air Compressor
• AC Package and custom Electrical Package`
• Concept 6,000 lb. Hydraulic Liftgate
• Concept Adjustable Second Level Deck
• Concetp Custom Fold-up Adjustable Forward Deck
• Custom Lower Level Deck/Workbench System
• Custom Front Wall Cabinet Module
• Custom Nitrogen Bottle Rack
• Built in tool boxes and parts storage
• Deluxe Awning Package and Observation Deck
53’ Smooth Side Custom Semi Trailer
• 37” drop at fi fth deck and 5” drop at suspension module
• 106” fl oor to ceiling forward of drop
• 143” fl oor to ceiling rear of drop
• 138” fl oor to ceiling above suspension and to rear of trailer
• 36” king pin setting
• 144” inside length fi fth deck floor
• 49-1/2” coupler height
• 42’- 5” center of king pin to center of rear axle (Bridge length)
• 4” steel I beam sills on 12” centers
• Neway air-ride suspension
• (2) Rockwell 3” drop axles
• Rockwell anti-lock brakes
• 16-1/2” x 7” brake shoes
• Goodyear G-114 255-70R 22.5 16 –ply tires
• 1’3/8” ship lapped hardwood fl oor
• Special radiused front vertical corners
• Natural aluminum top and lower rails
• .090 natural aluminum, smooth side exterior panels
• 14 gauge double slotted logistic posts on 16” centers
• Plastic faced Todco roll-up rear door
• .040 stretched one-piece aluminum roof coil
• Steel roof bows on 24”
Custom Side Access Doors
• 60” x 84” double doors (Curbside)
• 10ga. Formed structural steel perimeter doorframe inside trailer wall
• 10ga. Formed steel header inside trailer wall below top rail
• Structural reinforcement added to cross members and fl oor in door area
• Composite door construction
• Rivetless interior and exterior construction
• Brushed stainless steel door perimeter trim
• Lightweight 14ga. Formed steel door structure
• .050 5052-H32 pre-painted white aluminum exterior panels
• .050 5052-H32 pre-painted white aluminum interior panels with extruded aluminum edge molding
• All steel surfaces primed for rust prevention
• All exposed steel surfaces painted white
• Recessed polished stainless steel Furgocar lockable door latches with concealed hardware
• Long lasting corner mounted door seal
• Stainless steel continuous hinge with internal compression seal
• 12ga. Brushed stainless steel threshold and entry frame
Concept Exterior Trim Kit
• Concept custom fiberglass tandem axle fender enclosures
• Concept custom fiberglass front quarter fenders and fi ller panel
• Rivetless drop extension trim with tapered rear
Deluxe Nose Mount Generator Air Compressor Enclosure
• 20 Kw water-cooled diesel generator mounted on top shelf
• 55-gallon fuel tank
• Sound suppression package
• Steel tube interior construction (Painted black)
• (4) 430 bright stainless steel doors with lockable T-handle latches
• Exterior skin pre-painted white aluminum surround
• Radius riveted vertical corners
• Heat rap on internal vertical exhaust components
• In-line circuit breaker
• Remote start-stop panel with meters for generator installed inside trailer behind side access door
• Squirrel cage fan blower added for forced air circulation
• 3-hp air compressor with 20-gallon tank mounted on center shelf
• (3) interior quick couplers (Curbside)
• (3) exterior quick couplers (Curbside)
Concept 6,000 lb. Hydraulic Liftgate
• Lightweight steel frame platform construction
• 144” long 3/16” 6061-T6 aluminum diamond plate load surface
• Rivetless .090 aluminum exterior skin
• (6) Recessed polished stainless steel taillights
• Custom tapered aluminum fl ip-over transition ramp
• Custom aluminum diamond plate fl ip-over extension: (for use in loading low ground clearance cars)
• Formed foldout painted steel corner covers with stainless steel hinges and transition panels
• Formed steel header with extra clearance lights
• Custom 12V/220V combination hydraulic power unit
• Power unit mounted behind fenderwell on roadside
• (3) 12V group 27 batteries mounted behind fenderwell on curbside
• Automatic battery charger
• (2) 300-watt quartz load lights
• Remote operating control box with extension cord
• Nylon load and closing chain covers
• Provisions for (2) license plates
• Nickel-plated chain clevis links and grab hooks
• Interior framework primed and painted for rust prevention
Deluxe Air Conditioner Package
• 15,000 Btu single zone ductless A/C system
• Evaporator mounted on front wall of trailer
• Condenser mounted on first shelf of nose mount box
Interior Modifications
Interior Upgrades
• 1” ridged foam insulation in walls and ceilings
• Installed white ABS plastic panels between logistic posts from floor to ceiling
• Pre-painted white aluminum ceiling
• ( 8) 12V dome lights in ceiling
• (3) 12V electric roof vents with fans and rain sensors
• All screw holes filled in floor
• (1) coat of special penetrating hardwood floor sealer
• (2) coats of oil modified polyurethane hardwood floor finish
• Custom pre-painted white aluminum and brushed stainless steel covers panels on walls above fenderwells and at front drop
Concept Custom Adjustable Second Level Deck
• Approximately 40’-6” long starting a rear of trailer
• Deck clips into slots in logistic posts
• Lightweight formed steel platform construction
• Custom tube frame supports for extra clearance below deck
• Load surface is 27” overall width (each side)
• Ramp finished, white powder coat
• Grey rubber diamond plate load surface, full length
• Full-length surface mounted radius corner aluminum V-track #3, installed on inner vertical surfaces, both sides. Track top edge held even with rubber surface
Concept Custom Fold-up Adjustable Second Level Deck (Forward Section)
• Approximately 8’ long starting at end of adjustable deck (Both Sides)
• Deck clips into slots in logistic posts
• Lightweight formed steel platform construction
• Custom tube frame supports for extra clearance below deck
• Load surface is 27” overall width (each side)
• Ramp system, powdercoat finish white
• Removable nickel-plated load bars
• Grey rubber diamond plate load surface, full length
• Full-length surface mounted radius corner aluminum V-track #3, installed on inner vertical surfaces, both sides. Track top edge held even with rubber surface
• Deck folds-up and clips into wall
Custom Lower Deck Workbench System
• Full length, main trailer floor
• 30” tall: (approximately 27” clear storage under)
• Aluminum tube frame construction
• Formed 1/8” smooth aluminum load surface
• Reinforced underneath for additional support
• Grey rubber diamond plate load surface, full length
• Full-length V-track #3 mounted to inside vertical edge of deck. Track top edge held even with rubber surface
• Full-length anodized aluminum frame with custom aluminum frame composite doors
• Laminate interior and exterior finishon door enclosures
• Grey positive latching hardware
• Custom removable transition ramps to allow loading of cars into fifth deck
• (2) Custom Lista cabinets installed in roadside bench approximately 6’ back from drop
Custom Front Wall Cabinet Module
• Custom aluminum frame cabinets (Matching laminate cabinet doors)
• Full width upper cabinets
• Open section for A/C evaporator
• Full height wardrobe sections along bottom
Concept Custom Nitrogen Bottle Rack
• Custom built bottle rack to house (4) K-size nitrogen bottles
• Bottle rack installed under curbside workbench just behind side door
• Swing-out door access
• Line connection inside compartment with quick disconnect fitting under trailer exterior below side access door.
Custom Electrical Package
• 100amp electrical distribution panel
• Electrical panel mounted on (curbside) trailer wall in front of side door
• (12) corner mounted 4’ fluorescent 2 –tube light (6) per side, spaced evenly over full-length trailer length in upper corners
• (2) 110V exterior electrical duplex outlets on (curbside under trailer)
• (4) 110V interior duplex receptacles: (1) below main panel, (1) at rear of curbside bench, (1) at center of curbside bench, and (1) at front of roadside bench
• (2) 220V interior outlets: (1) below main panel, (1) at rear of curbside bench
• (3) exterior 100V 500W T-slot mounted quartz lights on curbside
• (7) exterior 100V duplex outlets for power to awning fans and 500W quartz lights, (2)-switches for power: (1) for lights and (1) for awing power
• All light switches outlet switches, generator controls. Main breaker panel, etc., installed in stainless steel enclosure located between the trailer drop and the curbside access door.
• Shore power plug
• Manual transfer switch
• All exposed electrical wiring installed in conduit and concealed wherever possible
Concept Stainless Interior Trim Package
• Polished and brushed stainless steel
• Full floor perimeter on fifth deck, ceiling perimeter, etc.
• Brushed stainless steel in high traffic areas
Custom Additions and Accessories
• (1) custom formed low profile full width aluminum side entry step
• Canepa Design “Indy Style” Alcoa polished aluminum wheels
• Canepa Design “ center lock” chrome plated aluminum wheel covers
• Black non-script rear mud flaps
• Conspicuity tape full perimeter
• Front underside weather guard
• (1) fi re extinguisher
• (3) industrial quality floor mat runners
Concept Deluxe Awning Package
• 52’ x 22’ awning, 86” eve height
• Lightweight anodized aluminum frame construction
• Aluminum and stainless steel mounting hardware
• Lightweight radiused corner rectangle rafter poles with spinnaker ends “fi re retardant”
• High quality water resistant Grey 5oz. Dacron sailcloth main canvas
• Custom zip-0ff bead track strip for easy set-up and tear-down
• Zippered rafter pole pockets
• Buckle straps on all horizontal poles
• High quality water resistant Grey 5oz. Dacron sailcloth full enclosure walls (with black vinyl soil skirt) :fi re retardant”
• Zippered vertical post pockets
• (2) Custom end vents (1) each end: End vents to extent to the mid-span pole on the awning and match the profi le of the end of the awning
• (5) rain drains (1) each bay
• Heavily reinforced at chafe and stress areas
• Complete black vinyl bag set: including (2) pole bags (1) main canvas tube bag and (1) standard canvas bag for sidewalls
• Complete tie down kit: including spikes, posts, ropes with brass clasps, hammer, and storage pouch with bag
• Specially designed rafter pole storage brackets on roadside wall below 2nd level deck.
Concept Deluxe Awning Accessory Package
• (6) rafter poles wired and electrical outlets: (1) in center of pole and (1) at the end
• (6) Custom cords to connect awning poles to trailer exterior outlets
• (4) Lighted ceiling fans with remotes attached to custom made aluminum brackets that pin into rafters
• (4) Lights attached to custom made aluminum brackets that pin into rafters
Concept Custom Observation Deck
• 20’ long x 8’-1/2” wide
• Mounted at rear of trailer
• Additional structure added to roof of trailer
• 1/4” aluminum diamond plate load surface
• Deluxe stainless steel tubing fold down handrails
• Custom center ridge 5ox Grey Dacron sailcloth canopy
• Custom black mesh full perimeter hospitality panels
Custom Built Observation Deck Access Stairs
• Approximately 32” wide
• Custom narrow depth construction
• (1) stair system from ground to liftgate at approximately mid height
• (1) stair system from liftgate to roof top observation deck
• Custom-machined safety pins for liftgate side tube stops
• 1/8” formed aluminum construction
• No skid surface applied to each step
• ( 2) Removable hand rails per stair section
Custom Tie-down Accessories
• (50) Blue E-to-D tie down clips
• (36) Custom made blue (12” fixed end) ratchet straps
• (36) Customer made blue axle straps with protective sleeve
Exterior Workbench Package
• (2) 8’ aluminum exterior workbenches
• (2) Stainless steel T-slot exterior mounts per bench (curbside behind side door)
• (3) Removable aluminum support legs per bench U.H.M.W. wear pads on trailer side rail
• (2) Aluminum logistic posts clips for use in clipping into wall during storage/transit
Custom Exterior Paint
• Complete (one) color paint including upper and lower extrusion rails
• Remove all conspicuity tape, clearance lights, and reflectors, etc.
• Sand all exterior surfaces
• Mask off entire roof and all stainless steel surfaces
• Primer all surfaces with highest quality acid etching primer
• Prep and fi ne-sand all surfaces for finall paint
• Paint trailer exterior (white code 12)
• Install new conspicuity tape, clearance lights, and reflectors
• Color sand, polish and wax to show quality finish
